How to apply our products

stickers

– Make sure the surface is totally smooth / not textured;
– Clean the surface you wish to cover with a degreaser (make sure the surface is dry before applying the tile stickers);
– For a better and durable finish use a hairdryer and apply heat to the already applied stickers and with a smooth cloth make pressure. Make sure you do this process also on the edges.
– Do not clean the tile stickers with abrasive materials;
– Do not apply tile stickers to walls with latex or silicone-based paints; freshly painted walls (allow to dry for about 3 weeks).

remove

For a better and durable finish use a hairdryer and apply heat to the already applied stickers. The heat will activate the glue, letting the stickers be removed easily.

1 – Clean the surface, if possible use a degreaser. Make sure that surface is free of dust, dirt and moisture. Let it dry and you can start the application process of your tile stickers.

2 – Peel 1/2 inc | 1 cm and crease back paper.  Align the tile sticker with the top of the tile. Check the alignments and with a finger stick it to the tile.

3 – With a soft cloth apply the tile sticker. If you find any bubbles or want to realign you can always lift and put it back. Avoid non-flat areas like rounded tile edges or tile grout.

4 – The best way to finish is by using a hairdryer. Heat the tile decal and with a soft cloth press firmly against the tile. This process will activate vinyl glue and will give you the best results.

5 – In the finishing process (heat the tile sticker and press soft cloth) focus on tile sticker edges.
If at any moment (1 day or 1 year) after you see an edge peeling off use this process.

VIDEO

1 – Align the sticker on the wall and hold it in position with paper tape. Pass over with the squeegee to flat the sticker.

2 – Apply the paper tape vertically right in the middle. This will be the final position for your sticker.

3 – Grab the left half and gently pull the transfer paper (top layer). The vinyl should stick to the transfer paper. If it does not, try to paddle a little more on that area. Then, cut the paper liner (bottom layer).

4 – Beginning from the center of the sticker (above the tape) paddle from the center outward, always from the middle to the borders.

5 – Remove the paper tape and repeat the 3rd step, this time on the right side.

6 – Wait about 10 to 15 minutes. Then, gently begin to remove the transfer paper, pulling backwards and parallel to the wall, confirming that your sticker stays on the wall.

1 – Clean the surface and make sure that it is free of dust, dirt and moisture. Let it dry.

2 – Take the first strip, peel back the backing sheet approximately 20 cm and sharply crease the liner. DON´T peel all the backing off.

3 – Position and align the first strip on the wall. Make sure it is in a perfectly vertical position.

4 – Take the squeegee supplied and paddle from the center outward, eliminating all the air bubbles.

5 – Carefully, pull the paper and keep using the squeegee until you reach the bottom of the strip.

6 – With a hair dryer apply heat to activate the glue. At the same time, use the squeegee and press firmly. Repeat the every step for each strip.

PVC

1 – Apply the cardboard stencil provided using a level and paper tape. This is where you will be applying your PVC decoration.

2 – Use glue (or double sided tape) to apply the PVC letters.

3 – Apply the letter where it fits in the stencil.

4 – When you have applied all the letters wait about 10-15 minutes and gently remove the cardboard stencil.

PVC + VINYL

1 – Align the sticker on the wall and hold it in position with paper tape. Pass over with the squeegee to flat the sticker.

2 – Apply the paper tape vertically right in the middle. This will be the final position for your sticker.

3 – Grab the left half and gently pull the transfer paper (top layer). The vinyl should stick to the transfer paper. If it does not, try to paddle a little more on that area. Then, cut the paper liner (bottom layer)

4 – Beginning from the center of the sticker (on top of the paper tape) paddle from the center outward, always from the middle to the borders.

5 – Remove the paper tape and repeat the 3rd step, this time on the right side.

6 – Wait about 10 to 15 minutes. Then, gently begin to remove the transfer paper, pulling backwards and parallel to the wall, confirming that your sticker stays on the wall.

7 – Use glue (or double-sided adhesive tape) to apply the PVC letters.

8 – Apply the letters to the wall using the alignment marks.

1 – With the help of the cardboard ruler provided, draw the locations where the screw hook will be.

2 – Drill the ceiling at the marked locations.

3 – Insert the wall plugs provided with the pack.

4 – Place the screw hooks.

5 – Hang an S hook on each screw hook hanger. Then interconnect the panels using the S hooks in order to complete the first row of panels.

6 – After placing the first row, repeat the process for the rest.

1 – Clean the surface and make sure that it is free of dust, dirt and moisture. Let it dry.

2 – Apply double-sided adhesive tape to the back of each panel.

3 – Start applying by aligning the panel to the upper left corner of the first door. Apply pressure where the tape was placed.

4 – After applying the first panel, repeat the process for the rest of the panels. The process of application is the same for every furniture model.

VIDEO

NOTE:
The process of application is the same for every furniture model.

1 – Clean the surface and make sure that it is free of dust, dirt and moisture. Let it dry.

2 – Apply the velcro pieces where you think it’s best or use a glue of your choice. You may use liquid nail glue, double-sided tape or silicone.

3 – Start applying by aligning the panel to the upper left corner of the wall. Make sure it’s leveled and will work with the panel you will apply on the right and bottom. Apply pressure where the velcros were placed.

4 – Once the first panel is installed, the next one should be placed side by side.